Perkins珀金斯850-854F柴油發動機T414523交流充電發電機供應商，Perkins珀金斯850-854F柴油發動機T414523交流充電發電機技術價格規格咨詢服務，Perkins珀金斯850-854F柴油發動機T414523交流充電發電機零配件供應，Perkins珀金斯850-854F柴油發動機T414523交流充電發電機售后服務中心，Perkins珀金斯850-854F柴油發動機T414523交流充電發電機，Perkins珀金斯850-854F柴油發動機T414523交流充電發電機詳細的技術參數，
Perkins珀金斯850-854F柴油發動機T414523交流充電發電機
詳細描述
項目 零配件號碼 最新件號 描述
1 T414523 1 T414523 交流充電發電機
2 T412615 1 T412615 桿
3 T412622 1 T412622 螺旋
4 2318 A208 1 2318 A208 螺帽
5 2314 J003 2 2314 J003 螺旋
6 T412378 1 T412378 螺帽
7 T411846 1 T411846 交流充電發電機托架
8 2314 J008 2 2314 J008 螺旋
9 2318 A604 1 2318 A604 螺帽
10 T412190 1 T412190 墊圈
11 T412377 1 T412377 螺旋
12 T412190 1 T412190 墊圈
|
Piston and connecting rod assemblies |
|
4 |
|
Big end bearing and cap |
|
To remove and to fit |
|
Operation 4-1 |
|
Special requirements Torque Nm (lbf ft) kgf m |
|
Clearance mm (in) |
|
102-05, 103-07 |
|
23 (17) 2,3 32 (24) 3,2 52 (38) 5,3 |
|
Standard |
|
Service limit |
|
103-10 |
|
0,1 - 0,3 (0.004 - 0.012) |
|
0,7 (0.276) |
|
103-13, 103-15, 104-19, 104-22 |
|
Ensure that when the connecting rods are fitted an axial play (clearance) is provided. During assembly apply a thin layer of clean engine lubricating oil to the crank pins with. |
|
Notes: |
|
Identify each rod/piston/cylinder pair on disassembly. |
|
For emissions approved engines. The fuel adjustment screws must not be altered from the original settings. For emissions approved engines. The maximum No Load Speed must be checked after assembly. If new connecting rods are fitted, see Operation 3-13. |
|
Workshop Manual, TPD 1377E, issue 4 |
|
49 |
|
This document has been printed from SPI². Not for Resale |
|
4 |
|
100 Series |
|
Piston and connecting rod |
|
To dismantle and to assemble |
|
Operation 4-2 |
|
Align Shibaura logo (A1) with stamped number on con rod. Align numbers to match (A2). |
|
1 |
|
2 |
|
50 |
|
Workshop Manual, TPD 1377E, issue 4 |
|
This document has been printed from SPI². Not for Resale |
|
4 |
|
100 Series |
|
To fit |
|
Operation 4-3 |
|
Special requirements |
|
Torque Nm (lbf ft) kgf m |
|
102-05, 103-07 103-10 |
|
23 (17) 2,3 |
|
103-13, 103-15, 104-19, 104-22 |
|
52 (38) 5,3 |
|
32 (24) 3,2 |
|
For positioning of connecting rod assembly refer to Operation 4-2. |
|
Note: Pistons must be fitted with Shibaura name toward the fuel injection pump. |
|
Workshop Manual, TPD 1377E, issue 4 |
|
51 |
|
This document has been printed from SPI². Not for Resale |
|
4 |
|
100 Series |
|
Piston and piston ring |
|
To inspect |
|
Operation 4-4 |
|
Any letters or marks on a surface of a ring (A1) will always be to the upper face. The piston profile shows the No.1 ring (A2), No.2 ring (A3) and the oil scraper ring (A4). |
|
1 |
|
2 3 4 |
|
52 |
|
Workshop Manual, TPD 1377E, issue 4 |
|
This document has been printed from SPI². Not for Resale |
|
4 |
|
100 Series |
|
To measure piston ring clearance |
|
Operation 4-5 |
|
By use of feeler gauges, measure the clearance between the piston ring groove and ring. If the clearance exceeds the service limit, renew the piston and rings. |
|
102-05, 103-07, 103-10 Clearance mm (in) Standard |
|
103-13, 103-15, 104-19, 104-22 Clearance mm (in) |
|
Piston ring |
|
Service limit |
|
Piston ring |
|
Standard |
|
Service limit |
|
0,06 - 0,1 (0.0024 - 0.0039) |
|
0,25 (0.0098) |
|
0,07 - 0,11 (0.0028 - 0.0043) |
|
0,25 (0.0098) |
|
No. 01 ring |
|
No. 01 ring |
|
0,05 - 0,09 (0.0020 - 0.0035) |
|
0,25 (0.0098) |
|
0,04 - 0,08 (0.0016 - 0.0032) |
|
0,25 (0.0098) |
|
No. 02 ring |
|
No. 02 ring |
|
0,02 - 0,06 (0.0008 - 0.0024) |
|
0,15 (0.0059) |
|
0,02 - 0,06 (0.0008 - 0.0024) |
|
0,15 (0.0059) |
|
Oil control ring |
|
Oil control ring |
|
Workshop Manual, TPD 1377E, issue 4 |
|
53 |
|
This document has been printed from SPI². Not for Resale |